Standard: JT/T 808-2013 (2013 Edition)
Terminal Configuration

Terminal Parameters Catalog (Table 3)

Standard range 0x0001 - 0xEFFF originates from national standard JT/T 808-2013. Extended range 0xF000 - 0xFFFF represents proprietary telematics parameters engineered for Jimi VL502.

Total Parameters: 100 / 100
Parameter IDData TypeDescription & Default SettingsDefault Value
0xF000-0xFFFFDWORDUser-defined extended parameter range for Jimi IoT / Concox VL502 terminal.-
0xF000-0xF1FFDWORDTerminal attributes, hardware info, and network management parameters.-
0x0001DWORDTerminal heartbeat sending interval. Unit: seconds (s). Default: 30.30
0x0002DWORDTCP message response timeout interval. Unit: seconds (s). Default: 5.5
0x0003DWORDTCP message retransmission times when acknowledgement is not received. Default: 3.3
0x0010STRINGMaster server APN, wireless communication dial-up access point. If CDMA, PPP dial-up number applies.-
0x0011STRINGUsername for master server APN dial-up authentication.-
0x0012STRINGPassword for master server APN dial-up authentication.-
0x0013STRINGMaster server address (IP address or domain name).-
0x0018DWORDMaster server TCP listening port.-
0x0081DWORDProvince ID where the vehicle is registered.-
0x0082DWORDCity or county ID where the vehicle is registered.-
0x0083STRINGMotor vehicle license plate issued by the traffic management department.-
0x0084BYTELicense plate color code (JT/T 415-2006): 0x00: Unlicensed, 0x01: Blue, 0x02: Yellow, 0x03: Black, 0x04: White, 0x05: Green, 0x09: Other.-
0xF000WORDDevice manufacturer code (Read-only).-
0xF001WORDAuthentication security level: 0x0001: SN only, default: SN + ICCID, or SN + ICCID + vehicle info.-
0xF002DWORDTerminal Serial Number (SN) in BCD[6] format (Read-only).-
0xF003BYTETerminal model/type code in BYTE[5] format (Read-only).-
0xF004BYTETerminal unique hardware ID in BYTE[7] format (Read-only).-
0xF005STRINGTerminal hardware revision version number (Read-only).-
0xF006STRINGTerminal system software/firmware version number (Read-only).-
0xF007STRINGIMEI, IMSI, and ICCID of the SIM card (Read-only, format: IMEI:xxx;IMSI:xxx;ICCID:xxx;).-
0xF008STRINGFTP server parameters for FOTA remote firmware upgrade: IP, port, username, password.-
0xF009DWORDFuel/oil consumption correction factor.-
0xF00ADWORDOdometer mileage correction factor.-
0xF00BDWORDInitial accumulated fuel volume baseline (calculated in Liters).-
0xF00CDWORDInitial accumulated odometer mileage baseline (in Kilometers).-
0xF00DDWORDVehicle type code: High 16-bit for commercial vehicles, Low 16-bit for passenger cars (Table 5).-
0xF00EDWORDReporting interval for OBD data stream transparent transmission. Unit: seconds (s).-
0xF00FBYTESub-categories of uplink transparent messages: 0x01: OBD stream, 0x02: DTC trouble codes, 0x03: Alarm & driving behavior, 0x04: Trip data, 0x06: CAN learning data.-
0xF010BYTETerminal registration state: 0: Not registered, 1: Registered.-
0xF011DWORDHardware fault mask bitmask. All 0 indicates normal hardware condition (Read-only).-
0xF012BYTEGeofence shape configuration: 0x00: Circular, 0x01: Rectangular.-
0xF013BYTEClear OBD diagnostic trouble codes (DTC). Set to 0x01 from platform to execute clear.-
0xF015BYTEVehicle diagnostic self-check control (0x01 to trigger check).-
0xF016BYTEOBD communication and diagnosis master switch: 0x00: Disable, 0x01: Enable (default).0x01
0xF017BYTEDiagnostic protocol communication switch: 0x00: Disable, 0x01: Enable.-
0xF018BYTESign flags for latitude (North/South) and longitude (East/West) of Geofence.-
0xF019BYTERemote GNSS/GPS power switch: 0x00: Off, 0x01: On (default).0x01
0xF01ABYTETerminal WiFi hotspot switch: 0x00: Off, 0x01: On (default).0x01
0xF01BBYTEReset WiFi SSID and password to default values (0x01 to execute).-
0xF01CSTRINGConfiguration string for WiFi SSID and password (Format: SSID:xxx;PASS:xxx;).-
0xF01DSTRINGSecondary network APN channel address.-
0xF01ESTRINGTarget server URL path for uploading terminal system debug logs.-
0xF01FBYTEVehicle anti-theft security switch: 0x00: Off (default), 0x01: Armed/On, 0xFF: Not supported.0x00
0xF020BYTEData encryption toggle: 0x00: Non-encrypted, 0x01: Encrypted payload.0x00
0xF021STRINGConfiguration parameters for external connected peripherals (RS232/RS485 sensor).-
0xF022STRINGQuery message format for external peripheral parameters (Read-only).-
0xF023BYTEAlarm threshold parameters for abnormal fuel level drop/theft detection.-
0xF024BYTENB-IoT network sharing mode: 0x00: Not shared, 0x01: Shared.-
0xF025STRING17-character standard Vehicle Identification Number (VIN).-
0x0020DWORDPosition reporting strategy: 0: By time interval, 1: By distance interval, 2: Combined time & distance.0
0x0021DWORDPosition reporting condition: 0: Depends on ACC state, 1: Depends on login and ACC state.1
0x0027DWORDReporting interval when terminal is in sleep mode. Unit: seconds (s), default: 3600.3600
0x0028DWORDReporting interval when emergency SOS alarm is active. Unit: seconds (s), default: 5.5
0x0029DWORDDefault regular position reporting interval. Unit: seconds (s), default: 10.10
0x002CDWORDDefault distance interval for position reporting. Unit: meters (m), default: 50.50
0x002EDWORDDistance reporting interval during sleep mode. Unit: meters (m), default: 50.50
0x002FDWORDDistance reporting interval during emergency alarm. Unit: meters (m), default: 20.20
0x0030DWORDHeading turning angle threshold for additional position report point: <180 deg, default: 30.30
0x0031WORDIllegal displacement / geofence alert radius threshold. Unit: meters (m), default: 500.500
0x0050DWORDAlarm mask word: Bitmask corresponding to alarm flags in 0x0200. Bit set to 1 masks the alarm.-
0x0055DWORDOver-speed limit threshold. Unit: km/h, default: 100/120.100
0x0056DWORDDuration threshold for over-speed condition before triggering alarm. Unit: seconds (s), default: 30.30
0x0057DWORDFatigue driving continuous driving time threshold. Unit: seconds (s), default: 4 hours (14400s).14400
0x0058DWORDFatigue driving cumulative driving time per day threshold. Unit: seconds (s), default: 8 hours (28800s).28800
0x0059DWORDMinimum mandatory rest time to reset continuous driving counter. Unit: seconds (s), default: 20 min (1200s).1200
0x005ADWORDMaximum allowable parking duration without ignition off. Unit: seconds (s), default: 3600s.3600
0x005BWORDDifferential pre-warning value before speed alert is triggered. Unit: 1/10 km/h, default: 10 (1 km/h).10
0x005CWORDDifferential pre-warning time before fatigue driving alert triggers. Unit: seconds (s), default: 1800s (30m).1800
0x005DWORDVehicle collision crash alert parameters: b7-b0: Duration (4ms unit); b15-b8: Acceleration (0.1g unit, default 10 = 1.0g).10
0x005EWORDVehicle rollover inclination angle threshold. Unit: degrees, default: 30 degrees.30
0xF200BYTEUser-defined alarm mask word for VL502 driving behavior and telematics events.-
0xF201DWORDHigh battery/input voltage alarm threshold. Unit: mV, default: 15000/28000 mV.15000
0xF202DWORDLow battery/input voltage alarm threshold. Unit: mV, default: 10800/20000 mV.10800
0xF203WORDHigh engine coolant water temperature alarm threshold. Unit: °C, default: 120°C.120
0xF204WORDLow engine coolant water temperature alarm threshold. Unit: °C, default: 60°C.60
0xF205WORDHigh engine oil temperature alarm threshold. Unit: °C.-
0xF206WORDHigh fuel temperature alarm threshold. Unit: °C.-
0xF207WORDHigh engine oil pressure alarm threshold. Unit: kPa.-
0xF208WORDEngine preheating duration alarm threshold. Unit: minutes, default: 10 min.10
0xF209WORDEngine excessive idling duration alarm threshold. Unit: minutes, default: 20 min.20
0xF20ABYTERapid throttle opening / aggressive acceleration threshold. Default: 40% pedal travel.40%
0xF20BWORDSudden harsh acceleration speed delta threshold. Unit: km/h, default: 40 km/h.40
0xF20CWORDSudden harsh braking deceleration speed delta threshold. Unit: km/h, default: 60 km/h.60
0xF20DWORDSharp turn / aggressive cornering angle threshold. Unit: degrees, default: 60 degrees.60
0xF20EWORDHigh engine RPM alarm threshold. Unit: RPM, default: 2500 (diesel) / 3500 (petrol) RPM.2500
0xF20FDWORDLatitude of circular geofence center point (multiplied by 10^6).-
0xF210DWORDLongitude of circular geofence center point (multiplied by 10^6).-
0xF211DWORDLatitude of top-left corner (Point 1) of rectangular geofence (multiplied by 10^6).-
0xF212DWORDLongitude of top-left corner (Point 1) of rectangular geofence (multiplied by 10^6).-
0xF213DWORDLatitude of bottom-right corner (Point 2) of rectangular geofence (multiplied by 10^6).-
0xF214DWORDLongitude of bottom-right corner (Point 2) of rectangular geofence (multiplied by 10^6).-
0xF215BYTEVibration / G-Sensor alarm trigger threshold. Unit: 0.1g, range: 1 - 10.5
0xF216WORDSecondary harsh braking deceleration threshold. Unit: km/h.-
0xF217WORDInitial vehicle speed threshold required to trigger harsh braking evaluation. Unit: km/h.-
0xF218WORDVehicle speed threshold required to trigger sharp turn evaluation. Unit: km/h.-
0xF219WORDDuration threshold for evaluating sharp turn condition. Unit: seconds (s), default: 2s.2
0x595AWORDDefault terminal manufacturer code (0x595A represents Concox / Jimi IoT).0x595A
0x0002WORDTerminal authentication level: 0x0001: SN only, default: SN + SIM ICCID.SN+ICCID